增湿管道典型结构的比较分析

介绍了水泥厂增湿管道的几种典型结构，并分析了各种结构的优缺点，在最后给出了设计时选用的原则和建议。     

气藏平均地层压力跟踪计算新方法

平均地层压力是产能评价和动态分析的基础，准确、快速获取平均地层压力对高效开发气藏意义重大。基于地层压力随时间变化的规律，分析了平均地层压力的变化规律。研究结果表明：平均地层压力等效点仅随时间发生改变，平均地层压力的下降速率等于或者近似等于井底流压的下降速率。从封闭弹性驱动气藏的物质平衡方程出发，考虑偏差系数和井底流压随平均地层压力的变化，推导建立了平均地层压力跟踪计算新方法，根据生产数据可迭代计算平均地层压力。方法验证结果显示，采气速度和采出程度共同影响模型的计算结果。应用实例表明，跟踪计算法与压力恢复试井和物质平衡法之间的相对误差均较小，满足工程计算精度要求，且跟踪计算法不需依托生产测试数据，节约了测试费用，避免了测试占产。     

飞行器静电起电放电的研究进展

飞行器作为空天装备重要的载体,其表面结构和材料差异造成电势差时,易发生静电放电,严重威胁飞行器的运行安全.文章从飞行器表面静电起电研究动态、飞行器静电起电机理、飞行器静电起电测试方法等方面介绍了该领域国内外的研究动态,以及本团队在静电起电机理以及静电起电测试方法方面研究的主要成果.提出了飞行器摩擦起电和喷流起电的测试方法,获得了飞行器摩擦起电与温度、湿度、摩擦速度以及接触面积之间的关系,通过试验测得了飞行器喷流起电使得飞行器带负电的结论,并分析了当前研究存在的问题和重点研究方向,为飞行器静电防护设计和安全性评估提供参考.     

Experimental Investigation on Low-Velocity Impact Performance of 3D Woven Textile Composites

Applied Composite Materials - The objectives of this experimental study are to develop impact-resistant three-dimensional (3D) woven textile-reinforced composites as well as to clarify the...     

Multi-color Q-switched of neodymium-doped all-fiber laser based on tungsten disulfide saturable absorber

Journal of Materials Science: Materials in Electronics - In this paper, a Q-switched and three-color operation of Neodymium-doped silica all-fiber laser is realized, in which, a few-layer...     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.     

无黏土相盐水储层钻开液体系构建及其抗污染性能评价

采用NaCl/KCl/HCOONa复配欠饱和盐水作为钻开液的基础液相,自研的聚合物VIS-B作为流型调节剂,可酸溶的改性淀粉STA作为体系的降失水剂,Dua及Jqw作为暂堵材料,构建了一套无黏土相钻开液体系。该体系在密度1.10~1.28 g/cm^3间稳定可调,抗温可达130℃,具有较高的低剪切速率黏度和较好的润滑性能,且能有效抵抗各类储层污染物的污染,满足了Missan油田不同储层段的作业需求。     

Centimeter-scale low-damage micromachining on single-crystal 4H–SiC substrates using a femtosecond laser with square-shaped Flat-Top focus spots

Femtosecond (fs) lasers have been proved to be reliable tools for high-precision and high-quality micromachining of ceramic materials. Nevertheless, fs laser processing using a single-mode beam with a Gaussian intensity distribution is difficult to obtain large-area flat and uniform processed surfaces. In this study, we utilize a customized diffractive optical element (DOE) to redistribute the laser pulse energy from Gaussian to square-shaped Flat-Top profile to realize centimeter-scale low-damage micromachining on single-crystal 4H–SiC substrates. We systematically investigated the effects of processing parameters on the changes in surface morphology and composition, and an optimal processing strategy was provided. Mechanisms of the formation of surface nanoparticles and the removal of surface micro-burrs were discussed. We also examined the distribution of subsurface defects caused by fs laser processing by removing a thin surface layer with a certain depth through chemical mechanical polishing (CMP). Our results show that laser-induced periodic surface structures (LIPSSs) covered by fine SiO₂ nanoparticles form on the fs laser-processed areas. Under optimal parameters, the redeposition of SiO₂ nanoparticles can be minimized, and the surface roughness Sa of processed areas reaches 120 ± 8 nm after the removal of a 10 μm thick surface layer. After the laser processing, micro-burrs on original surfaces are effectively removed, and thus the average profile roughness Rz of 2 mm long surface profiles decreases from 920 ± 120 nm to 286 ± 90 nm. No visible micro-pits can be found after removing ~1 μm thick surface layer from the laser-processed substrates.     

反坦克导弹用热电池研究进展

反坦克导弹作为击毁坦克和其他装甲目标的武器装备,在国家安全领域具有重要地位.热电池作为反坦克导弹的能源系统,对导弹功能实现具有重要意义.围绕反坦克导弹用热电池快激活和瞬时高比功率技术,结合热电池电化学材料体系发展历史、现状,探讨了提升快激活能力,提高瞬时比功率输出能力的技术,并对技术发展趋势进行了展望.